1,000 Sq Ft Metal Roof Cost (2026)
A 1,000 sq ft metal roof runs about $7,000 to $14,000 installed in Florida (2026), or $3,000 to $6,500 for materials only.
These metal figures are an industry-reference estimate. Florida-specific pricing for this material is being sourced and will replace the placeholder ranges.
$700 to $1,400 per roofing square. Industry-reference estimate (Homewyse and RoofingCalc typical); Florida-specific pricing pending.
| Materials | $3,000 to $6,500 Metal and accessories for about 10 squares. |
| Labor | $2,480 to $4,650 Crew, install, and staging. The largest share of most jobs. |
| Tear-off and disposal | $1,040 to $1,950 Stripping the old roof and hauling it off. Rises with extra layers. |
| Permit and inspection | $480 to $900 Florida re-roof permit and final inspection. An approximate derived share. |
| Total installed | $7,000 to $14,000 Typical $10,500. Low, typical, and high across a normal range of roofs. |
Scaled from real Florida per-square pricing off a 30-square baseline; the permit share is an approximate derived figure. How we estimate →
What affects the cost of a 1,000 sq ft roof.
A 1,000 sq ft roof is about 10 roofing squares, one of the smaller jobs a Florida crew takes on. The price per square usually runs higher than it does on a large house, because the fixed parts of any re-roof do not shrink with the roof. Mobilizing the crew, pulling the permit, renting the dumpster, and hitting the contractor's minimum day all cost roughly the same whether the roof is 1,000 or 2,000 square feet, so on a small roof those costs spread across fewer squares.
At this size, complexity moves the total more than square footage does. A steep, cut-up 1,000 sq ft roof with valleys, dormers, and a second story can take as much labor as a simple 1,400 sq ft single-story ranch. Tear-off is the other swing factor: stripping two layers of old shingle roughly doubles the disposal weight and the dump fees, and it is common on older Florida homes that were overlaid once already.
Every Florida re-roof pulls a permit and a final inspection, and the building code requires a rated underlayment and a secondary water barrier in the wind zone, which is built into these ranges. Because the estimate scales linearly off a 30-square baseline, a small roof sits at the least accurate end of that model. Treat the number as a research starting point and get a measured quote before you budget.
A 1,000 sq ft metal roof costs about $7,000 to $14,000 installed in Florida in 2026, with a typical price near $10,500, or roughly $700 to $1,400 per roofing square. Metal costs more up front than shingles but lasts far longer. These figures are an industry-reference estimate; Florida-specific metal pricing is being finalized.
A 1,000 sq ft roof is about 10 roofing squares. Roof area is larger than a home's floor area because it follows the pitch and overhangs, so a 1,000 sq ft roof does not mean a 1,000 sq ft house. Metal panels are priced by the square, so the roof's square footage drives the estimate.
A metal roof typically lasts about 40 to 70 years in Florida, several times the life of an asphalt roof on the same 1,000 sq ft home. Standing-seam metal handles high wind well, which is why it is popular in Florida's coastal counties, and a metal roof usually qualifies for wind-mitigation insurance credits.
Florida homeowners insurance covers roof replacement when the damage is from a covered peril such as a hurricane, not from age and wear. A 1,000 sq ft metal roof runs about $7,000 to $14,000, and its long life and wind rating tend to make a home easier to insure and can earn wind-mitigation credits that lower the premium.
Price your roof.
Get a budget estimate for your exact home, then see a new roof on it.